Wastewater Collection System
The Wastewater Collection System is the combination of 1,025 miles of sanitary sewer lines, 17,500 manholes, 15 pumping stations, and all private service lines and connections that collect wastewater and transport it to the two municipal wastewater treatment facilities: Theresa Street and Northeast. The pipelines start out as 8" in diameter and increase to up to 96" as they enter the treatment plants.
The City of Lincoln has been operating a wastewater collection system since 1888. The original system collected and conveyed wastewater from the City to Salt Creek. The first wastewater treatment facility in Lincoln began operation in 1923 and was managed by Sanitary Improvement District No. 1. In 1957 the Sanitary Improvement District No. 1 deeded the original wastewater treatment facility to the City. This was the beginning of the Wastewater Division of Public Works. The treatment facility was located at 24th and Theresa Streets, where the Theresa Street Wastewater Treatment Facility still exists to this day. Since then the collection system has grown, and as a result a second wastewater treatment facility was constructed on the northeast side of the City. This treatment facility is identified as the Northeast Wastewater Treatment Facility and is located at N 70th Street and Salt Creek.
The City's wastewater collection system is considered a sanitary sewer system only and is not a combined sanitary/storm sewer system. That means the flows conveyed in the wastewater collection system are derived from residential, commercial and industrial wastewater sources. Storm water from street runoff, roof drains and other similar sources are not directed to the wastewater collection system, but go into separate facilities called the storm water system.
The purpose of the maintenance program is to provide scheduled cleaning maintenance and inspection of the sanitary sewer collection system. The system is designed to use gravity by following the drainage contours throughout the City. Beal Slough, Antelope Creek and Oak Creek are among the main drainage basins. Those basins are broken up into smaller sub-basins of which there are 140 in total throughout the City. The sanitary sewer mains and manholes within those sub-basins are then scheduled and targeted for maintenance and inspection as a group.
Cleaning of the pipelines is necessary to prevent stoppages from happening. A stoppage occurs when the pipe becomes clogged, and wastewater can no longer flow and starts to backup within the pipe. This backing up of wastewater could lead to a Sanitary Sewer Overflow (SSO). An SSO is defined as any overflow release, discharge, or diversion of untreated or partially treated wastewater from a sanitary sewer system. The two most common SSOs are basement backups and wastewater discharges from manholes.
Stoppages are caused by a variety of factors: debris; fat, oil and grease (FOGs); tree roots; and paper products. These factors intermingle within the pipelines and start sticking together to create a mass that can eventually become the full diameter of the pipe and causes it to clog. The City works very hard to keep this from happening as part of the Collection System Maintenance Program.
LWWS Goal and Benchmarking Standard of 20 or Lower
As you can see from the graph, the City does a pretty good job in keeping the number of stoppages low and under our target of 20 or less per year.
To help prevent stoppages the City uses "jet trucks" (see picture) to provide maintenance cleaning of the sanitary sewer system. Two manholes are opened on either end of the pipe segment to be cleaned. On the downstream end the jet nozzle is lowered into the bottom of the manhole. It is connected to the truck by a long, high pressure hose. The water pressure is turned on and the jet nozzle is propelled up the line, against the flow of water, until it reaches the upstream manhole. Then the nozzle is brought slowly backward while spraying a jet of water onto the interior walls of the pipe. This water knocks down debris, grease, some roots and cleans the inside of the pipe smooth again. The cleaned pipe is now free flowing and at full capacity once again. Most pipes are cleaned once every three years. Some pipes are cleaned as often as every three months.
Another maintenance effort involves the removal of tree roots from sanitary sewers. Tree roots can be a real menace, damaging sewers, catching debris and causing sewers to clog. Tree roots seek the moisture and nutrients offered by leaky pipe joints and service connections. Tree roots are most often found in vitrified clay pipes, which are often in parts of town built before 1980.
There are two ways to control the growth of roots within the collection system: mechanical cutting or herbicide application. Mechanical cutting involves attaching a cutting blade to the jet nozzle, which will spin inside of the pipe to cut the roots off. While this method is effective in removing the roots it does not keep them from growing back. The EPA approved herbicide method involves filling a pipe segment up with a foam the consistency of shaving cream. This foam does two things: 1) it kills the roots by contact, and 2) it stays adhered to the pipe walls and inhibits future root growth for a period of time. Neither of these methods cause damage to the trees above nor do they interfere with the wastewater treatment process.
Internal Pipeline T.V. Inspection
One of the critical components of the preventative maintenance program involves internal inspection of sanitary sewers using a T.V. camera. The camera has a rotating head, lights, and zoom functions which allows 360 degrees of viewing of the pipe interior. The camera is attached to a crawler which is remotely controlled. The camera is set in the upstream manhole and then moves down the pipeline along with the flow. There is a video cable attached to the crawler and camera providing power, control and video feed back to the TV van. The camera head is turned to view service connections and any defects found, which are then recorded and put into an asset management system. This information is then used to determine the conditional rating of that pipe segment and if immediate repairs are required or not. The video information is also used to determine the effectiveness of the pipeline cleaning and root control maintenance activities. New sanitary sewers are also inspected to make sure they were installed per plan and City specifications. The City's goal is to video inspect each pipe on a 12 year or less interval.
Sewer Line Repairs
The Collection section staff self-performs some sanitary sewer line and manhole repairs. City staff usually performs repairs on lines and manholes that are found to be in critical condition with signs of imminent failure. Other repairs are grouped together, bid out, and performed by contractors.
Types of pipeline repairs and rehabilitation
- Point Repairs – When less than a 5' section of pipeline needs to be replaced.
- Pipe Line Replacement – When a greater than 5’ section needs replacement, has is a low spot in the line, or when the line needs to be moved to an alternate location. This type of repair uses an open trench excavation method of construction.
- Pipe Bursting – When the entire line needs replaced, but the location and grade are still good. This method displaces the old pipe with a new pipe and requires only minor excavations.
- Cured in Place Pipe Lining – This method inserts a new pipe lining into the old pipe to increase structural strength and seal up any cracks and holes.
- Spot lining – This method inserts a new lining into an old pipe but only covers a 2-4' section
The City repairs and rehabilitates over 12,000 feet of pipeline yearly. The budgeting for the repairs can be seen in Wastewater's Capital Improvement Program (CIP) under the line item Selected Replacement. These CIP projects are reviewed and approved by the Lincoln City Council.
I/I Removal and Reduction
Infiltration/Inflow (I/I) is extraneous water that enters the sanitary sewer system. Inflow is water that is intentionally and illegally put into the collection system by sump pump connections, roof drains or foundation drains. Infiltration is water that enters through cracks or leaky joints. An important ongoing task is to locate and remove these sources of I/I. Excessive I/I can overload the sewer system, cause basement flooding and overload the sewage treatment facilities, which occurred during the 100-year storm events in October 2014 and May 2015. The quantity of wastewater inside of the collection system was five times the normal rate during those storms. The City is working on developing additional programs to mitigate I/I sources.
Capital Improvement Projects (CIP)
Large infrastructure upgrades to the Wastewater Treatment Plants or Collection System are detailed in the Capital Improvement Program. These CIP projects are reviewed and approved by the Lincoln City Council. That document outlines expected expenditures for infrastructure to increase treatment capacities and install new sanitary sewer trunk lines to match the expected growth of the City as outlined in the Comprehensive Plan.
Sanitary Service Problems
Our department provides 24-hour service to City of Lincoln customers. Employees are on-call to respond to service problems or questions throughout the year. If you experience sewer service problems, please call 402-441-7961. A field crew will investigate the nature of the problem as soon as possible.
If you have additional questions or comments regarding the Lincoln Wastewater System, the following contacts may be made at these numbers:
- For questions regarding construction and repair activities, complaints and maintenance program call: 402-441-7988
- For questions regarding current projects, capital improvement projects, funding, or sources of infiltration/inflow call: 402-441-7987